Power over USB
The Universal Serial Bus (USB) is designed to provide power as well as data communications. It can support 127 devices and has developed over the years from 1.5 Mb/s to 480 Mb/s. Currently (2014) a normal USB 2.0 has a low current limit of 100 mA and a high current limit of 500 mA at 5 V although a Thunderbolt connector is able to deliver 2 A at 5 V. Several years ago USB 3.0 was introduced which increased the theoretical bit rate by 10x’s to 5 Gb/s and raised the low current limit to 150 mA and the high current limit to 900 mA. More recently the USB 3.0 Promoter Group has announced a new specification which will allow USB 3.0 compatible sockets and cables to deliver up to 100 W by changing the voltage from 5 V to 20 V and increasing the current to 5 A.
USB also has limitations on the maximum cable length and in most cases this is restricted to 3m. With special cables this can be increased to over 6 m and with a USB bridge this can be extended to over 30 m. With such a large increase in power a single USB 3 SuperSpeed hub could be charging a laptop, powering an external hard drive as well as a second monitor. In future, TV manufacturers could include high-powered USB hubs to power nearby AV and communication equipment thereby reducing the need for multiple wall outlets.
Both USB and PoE (power over ethernet) bring power and communication functions together by using the data exchange capabilities to negotiate power need with the device in a number of incremental stages. This level of power control allows a common supply to deliver a range of different power profiles best suited to whichever device is connected to that particular port. For example, in the future a USB 3 might provide 60 W (20 V at 3 A) for a laptop or 5 to 10 W (5 V at 1 or 2 A) for an average smart phone.
The benefit of both of these systems is that they are well developed solutions that are supported by appropriate standards, research and testing. Components are readily available and system design expertise is relatively common.
In terms of network distribution efficiency both PoE and USB are still subject to conversion and distribution losses as any other network. Whilst a modern PoE injector may have a very efficient power supply, power is still converted from 230 V AC to approximately 50 V DC, distributed to the point-of-load and then converted again to what’s required by the end device. In the case of PoE the voltage is higher than USB potentially reducing its distribution losses although conductor sizes are relatively small.
In the domestic environment USB ports are much more common and could in the future be used not just for connecting between devices, for example a laptop and a peripheral, but also as an additional low voltage power outlet complimenting the existing 230 V wall outlet. This may reduce the need for individual power adapters and bulky 230 V plugs and sockets although where this is the case, USB sockets are still likely to be associated with a central device such as a TV or computer.
This article was created by --BRE. It was taken from The future of electricity in domestic buildings, a review, by Andrew Williams, published in November 2014.
[edit] Related articles on Designing Buildings Wiki
Featured articles and news
Licensing construction in the UK
As the latest report and proposal to licence builders reaches Parliament.
Building Safety Alliance golden thread guidance
Extensive excel checklist of information with guidance document freely accessible.
Fair Payment Code and other payment initiatives
For fair and late payments, need to work together to add value.
Pre-planning delivery programmes and delay penalties
Proposed for housebuilders in government reform: Speeding Up Build Out.
High street health: converting a building for healthcare uses
The benefits of health centres acting as new anchor sites in the high street.
The Remarkable Pinwill Sisters: from ‘lady woodcarvers’ to professionals. Book review.
Skills gap and investment returns on apprenticeships
ECA welcomes new reports from JTL Training and The Electrotechnical Skills Partnership.
Committee report criticises UK retrofit schemes
CIOB responds to UK’s Energy Security and Net Zero Committee report.
Design and construction industry podcasts
Professional development, practice, the pandemic, platforms and podcasts. Have we missed anything?
C20 Society; Buildings at Risk List 2025
10 more buildings published with updates on the past decade of buildings featured.
Boiler Upgrade Scheme and certifications consultation
Summary of government consultation, closing 11 June 2025.
Deputy editor of AT, Tim Fraser, discusses the newly formed society with its current chair, Chris Halligan MCIAT.
Barratt Lo-E passivhaus standard homes planned enmasse
With an initial 728 Lo-E homes across two sites and many more planned for the future.
Government urged to uphold Warm Homes commitment
ECA and industry bodies write to Government concerning its 13.2 billion Warm Homes manifesto commitment.
From project managers to rising stars, sustainability pioneers and more.
Places of Worship in Britain and Ireland, 1929-1990. Book review.